The 10 best pcie hard drive enclosure for 2022
Finding the best pcie hard drive enclosure suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
1. NVMe Enclosure PCIe M.2 2280 SSD Box,Type-C USB 3.1 NVME Solid State Hard Disk Case,HDD Enclosure
Feature
Radiating Advanced Aluminum Case, USB 3.1 Type-C to M key M.2 SSD enclosure for Intel 600P NGFF PCI express NVMeSupport Samsung 950Pro/ 960Evo/ PM951/ PM961/ SM951/ SM961/970 EVO /970 PRO and other M.2 SSDs with PCI-E (M-KEY) Interface Type. The PCI-E Interface Implements The NVMe Protocol Standard
Seamless Cloning and File Transfers with the Samsung Magician Software, the Ideal Ssd Management Solution For Performance Optimization and Data Security with Automatic Firmware Updates
The NVMe interface (PCIe M.2 2280) offers enhanced bandwidth, low latency, and power efficiency, perfect for tech enthusiasts, high-end gamers, and 4K & 3D content designers
NOTE:Only for M-Key M.2 SSD (PCI-E NVMe-based), doesn't support B-Key SSD(SATA-based) and M-Key M.2 SSD(PCI-E AHCI-based), applicable to size 2230 / 2242 / 2260 / 2280.
Description
product name:HDD EnclosureInterface:M.2 NVME/USB 3.1
Color:grey
weight:137g
Material:aluminum
size:L 105 x W 45 x H 14 mm
Installation Diagram:
1. Prepare the accessories before installation: Hardware aluminum housing (Figure: chassis with silicone gasket), bottom shell PCB board, NVMe SSD hard disk (face paste good silica gel sheet), screwdriver, bottom shell screws.
2. Insert the prepared SSD hard disk (must be PCIE) according to the direction regulation on the PCB board.
3. Buckle the golden copper pillars at the end of the SSD hard disk, and gently press the hard disk until the copper pillar chassis and the corresponding PCB copper holes coincide with each other.
4. Press the copper post and turn it over the back of the PCB board to lock the set screw.
5. Put the PCB board with SSD hard disk reversal into the case. Note: The Type-C connector must be installed in place.
6. After the PCB board is in place, fix the board with two screws on the locking plate.
7. The direction of the bottom shell cover (for the sake of beauty, the bottom of the product we use a lock design, just insert the bottom cover fastened, don't need screw to lock).
8. Press the bottom shell to be flat and lock the two screws at the front.
2. StarTech M.2 to U.2 Adapter - M.2 Drive to U.2 SFF-8639 Adapter - Works with M.2 PCIe NVMe Drives
Feature
Add the fast performance of an M.2 NVMe SSD to your desktop computer or server through a U.2 (SFF-8639) compatible interface on your motherboardM.2 to U.2 adapter for M. 2 NVMe SSDs
The M.2 drive adapter supports one M.2 PCIe NVMe SSD (M-Key) and provides a cost-effective way to add M.2 NVMe performance to your PC or server
Fast and easy setup with native OS support, and backward compatible with earlier versions of PCIe
M.2 Drive to U.2 (SFF-8639) host adapter / M.2 drive adapter with U.2 (SFF-8639) host interface / M.2 PCIe SSD adapter / NVME M.2 SSD Adapter / SFF-8639 Adapter
Description
This PCI Express M.2 to U.2 adapter makes it easy to install an M.2 PCIe NVMe SSD into your desktop PC or server, and connect to the drive through an available U.2 (SFF-8639) compatible interface on your motherboard. Upgrade your system cost-effectively The M.2 to U.2 adapter is ideal for IT professionals, system integrators and installers, and enthusiasts who are building or upgrading a server or desktop computer. It supports one M.2 PCIe NVMe SSD (M-Key),providinga cost-effective way to add M.2 NVMe performance to your computer or server through an available U.2 (SFF-8639) compatible interface on your motherboard. Easy installation The M.2 to U.2 adapter works with all desktop PCs and servers that have an available drive bay or a U.2 (SFF-8639) compatible host interface. The adapter card is OS independent, so there are no drivers or software required for installation. The U2M2E125 is backed by a StarTech.com 2-year warranty and free lifetime technical support.3. XT-XINTE NVMe PCIE USB3.1 HDD Enclosure M.2 to USB Type C 3.1 M Key SSD Hard Disk Drive Case External Mobile Box (Black)
Feature
Note: It doesn't support Samsung_Data_Migration. M-key connector , Only support Nvme Protocol; If your Hard disk protocol is NVME M.2, it can use with this driver case.Support system: WinXP/Vista/Win7/Win8/WIN10 32-bit/64-bit MAC10.8 or higher
Application : for 3D Game, 4K video ,HIFI Music, RAM Picture ect.
HDD Enclosure size: 125mm*40mm*10mm
Support interface: USB3.1 TO M.2 KEY-M
Description
Descriptions:Brand: XT-XINTE
Product model: NVMe HDD Enclosure
Main Chipset: Jmicron JMS583
Protocol: NVMe
Connector: TYPE-C
High Speed: 10Gbps
Case Color: Silver and Black
NVMe Supriority:
1. up theperformance
2. decrease delay
3. decrease power dissipation
4. IPOS of SSD will increase
Package include
1 x USB 3.1 Type-C NVME SSD Enclosure
1 x Type-C Cable
1 x Screwdriver
4. BGNing Aluminum NVMe PCIE USB3.1 HDD Enclosure M.2 to USB SSD Hard Disk Drive Case Type C 3.1 M Key Connector HDD Box Desktop PC
Feature
USB3.1 TYPE-C NVMe, Supports TRIM to the SSD, Material: AluminumSupport : 3D Game, 4K video ,HIFI Music, RAM Picture ect
Protocol : NVMe, Connector : TYPE-C, High Speed: 10Gbps
Supports USB Super-Speed/High-Speed/Full-Speed Operation
Supports USB2.0/USB3.1 Gen 1/2 power saving mode
Description
Noted:
M-key connector , Only support PCIE Protocol
For a new hard disk, if there have files, pls backup the data in first.
And then click My Computer--Device Manager--Storage--Disk Management, find the hard disk that is connected.
Set the partition, right click the Mouse to Initialize, then there will be a dialog box, go to the next step, the nest step, and is ok.
Compatibility
1. Only support M.2 supporting PCIE NVME protocol, Not support M.2 without PCIE AHCI protocol, Not support M.2 without SATA protocol, Products with NVMe logo can be applied to this product.
2. This product does not need to install drivers, supports plug and play and hot plug, suitable for all kinds of original machines with USB interface, compatible machines, notebook computers, tablets, Macs, mobile phones with OTG, etc.
3. Installing a new hard disk requires initialization before normal storage and copying. Different computer operating systems require different file types. When formatting, please select the file type suitable for your computer operating system.
Features:
Supports TRIM to the SSD
Integrates with USB Type-C multiplexer& configuration channel(CC)logic
Complies with PCI Express Base Specification Revision 3.1a
Complies with NVM Express 1.3
Complies with USB3.1 Gen 1 and Gen 2 Specification,USB Mass Storage Class,Bulk-only Transport Specification(Revision 1.0)
Complies with USB Attached SCSI Protocol(UASP)Specification(Revision 4)
Supports external SPI NVRAM for Vendor VID/PID of USB2.0/USB3.1 Gen 1/2 device controller
Thirteen GPIOs for customization
Provides hardware controlled PWMs
Provides software utilities for downloading the upgraded firmware code under USB2.0/USB3.1 Gen1,2
Design for Windows 7,Windows 10 and MAC 10.10.5 or later version
5. NVME Solid State Hard Disk Case, Type-C USB 3.1 NVME SSD Box,NVMe m.2 Enclosure PCIe M.2 SSD to USB 3.1 Type C Gen2 Enclosure.
Feature
🍃Stable and fast transmission speed:USB 3.1 Port support the speed of data transmission up to 10Gbps,give you a steady and efficient data transfer, Inteface: M.2/NVMe (internal),USB 3.1(external),10G movie transmission takes only 10 seconds,Data Security with Automatic Firmware Updates, Data copy and transferring will be done in no time, perfect for tech enthusiasts, high-end gamers, and 4K & 3D content designers.🍃Powerful cooling performance:Aluminum alloy shell,strong and durable,9 mm Radiating Advanced Aluminum alloy shell And increase the thermal conductive silicone,The whole body act as a heatsink with excellent heat dissipation;Easy installation, Hot-swappable, Plug & Play, No extra drive required ,Provides heat dissipation and data saver for your systems.
🍃Strong compatibility:Easy Setup, Hot-swappable, Plug and Play, No Driver requiredSupport Samsung 950Pro/ 960Evo/ PM951/ PM961/ SM951/ SM961/970 EVO /970 PRO and other M.2 SSDs with PCI-E (M-KEY) Interface Type,Compatible For Windows XP / Vista / 7 / 8 / 8.1 / 10 and Mac OS 10.1 and above, Linux.
🍃Need to pay attention:Only for M-Key M.2 SSD (The PCI-E Interface Implements The NVMe Protocol Standard),doesn't support B-Key SSD(SATA-based) and M-Key M.2 SSD(PCI-E AHCI-based),Work with NVME M.2 SSD (Key M), apply to 2230/2242/2260/2280mm.
🍃Best product quality assurance:The use of high-quality PCB circuit board, while improving the speed, can also ensure that your hard disk data will not be lost, even in harsh environments, can also escort you.18 Month Warranty and 3 Month Replacement Warranty, Support email Response within 24 Hours.
Description
product name:HDD EnclosureInterface:M.2 NVME/USB 3.1
Color:grey
weight:137g
Material:aluminum
size:L 105 x W 45 x H 14 mm
This product adopts Type-C interface, aluminum alloy shell design, surface shell with
trunking design and two side ventilation holes design, both beautiful and
enhanced heat dissipation effect, no need drive, hot swappable, and strong compatibility.
Data Security with Automatic Firmware Updates
The NVMe interface (PCIe M.2 2280) offers enhanced bandwidth, low latency, and
power efficiency, perfect for tech enthusiasts, high-end gamers, and 4K & 3D content designers
NVMe Supriority:
1. up theperformance
2. decrease delay
3. decrease power dissipation
4. IPOS of SSD will increase
Compatibility Note:
1.Compatible with PCIe NVME M-Key M.2 SSD ONLY! It does NOT fit SATA-based NGFF M.2 SSD.
2.Not support disks with AHCI logical interface. Some of disk offered both AHCI and
NVMe edition, for example: Samsung SM951. MZ-VPV5120 / 2560 will be supported ONLY!
3.Make sure your PC came with USB3.1 Gen2 port and drives was properly installed.
Some PC came with USB C port which does not mean that is USB3.1 Gen2.
4.Some NVMe may need to take off its heatsink to adapt to this enclosure.
For example: Plextor M8Pe, M9PeG and some of XPG.
5.The case will be heated up since NVMe producing a lot of heat. This is normal condition.
Package list
USB 3.1 to M.2 NVMe SSD case x1
USB 3.1 to type C cable x1
USB C Adapter x1
Screw kit x1
non-slip pad x2
Instruction manual x1
6. QNINE USB 3.0 PCIe SSD Enclosure for 2013 2014 2015 2016 2017 MacBook Air Pro Retina, A1465 A1466 A1398 A1502 SSD USB External Reader Adapter with Case
Feature
USB 3.0 to 2013 2014 2015 2016 2017 SSD Adapter Case Enclosure.Alow 2013-2016 macbook air/PRO Retina SSD to work as USB 3.0 external HDD case
DOES NOT support ALL the Toshiba SSD or OWC SSD, Samsung MZ-JPV2560/5120,MZ-KPV1TOT
Support Sandisk SD6PQ4M-128G, SD6PQ4M-256G SSD; Support Samsung MZ-JPU128T, MZ-JPU256T,MZ-JPU512T,MZ-KPU1TOT,MZ-JPV1280.
SSD formated in Mac OS systerm can't be compatible with Microsoft system,so new SSD without partition,ssd can't be shown in table of "My Computer", please use the Disk Manager in Windows to delete the old partitions and create a new partition.
Description
Attention:1. SSD in the photo not included in the package.
2. SSD formated in Mac OS systerm can't be compatible with Microsoft system,so new SSD without partition,ssd can't be shown in table of"My Computer', please use the Disk Manager in Windows to delete the old partitions and create a new partition.
3.Fit following SSD modules:
Samsung MZ-JPU128T/0A2, MZ-JPU256T/0A2,MZ-JPU512T/0A2,MZ-KPU1TOT/0A2,MZ-JPV1280
Sandisk SD6PQ4M-128G,SD6PQ4M-256G
NOT Support Toshiba THNSN2128GSPS,Samsung MZ-JPV128/2560/5120,MZ-KPV1TOT
3. Update BIOS to the latest version.
Description
This product is 2013-2014-2015 MACBOOK AIR/PRO Retina ssd SSD to USB adapter, it is allowed to use SSD from 2013 2014 2015 Macbook SSD module through USB3.0 port on your desktop or laptop.
Features:
1. Fit SSD modules only from the following Apple 2013 MACBOOK AIr PRO:
11" Air Mid 2013, A1465(MD711.MD712)
13" Air Mid 2013, A1466 (MD760.MD761)
13" PRO Retina Late 2013, A1502 (ME864, ME865, ME866)
15" PRO Retina Late 2013, A1398 (ME293, ME294, ME874)
2. Support Hi-Speed USB 3.0(5Gbps), PCIe Gen2 5Gb/s mass storage interface
3. Extra power needed if USB3.0 port can't provide enough power supply
Package included:
1x USB 3.0 to 2013 2014 2015 SSD Adapter Case Enclosure.
7. JSER SFF-8639 NVME U.2 to NGFF M.2 M-key PCIe SSD Adapter for Mainboard Replace Intel SSD 750 p3600 p3700
Feature
The adapter is SFF-8639 U.2 port not SATA/NGFF/M.2 port.(Please don't purchase it if you want to connect SATA or NGFF or M.2, they are difference interface)System requirement: A free U.2 SFF-8639 interface or A free SFF-8643 interface
Need M-key or NVME SSD, the B-key or B/M-key SSD cannot work.
Note: for M-key or NVME SSD, please Update to add native driver support in NVM Express in Windows 7 and Windows Server 2008 R2
Supports M.2 NGFF modules in format 2280, 2260, 2242 and 2230 with key M
Description
SFF-8639 NVME U.2 to NGFF M.2 M-key PCIe SSD Adapter for Mainboard Replace Intel SSD 750 p3600 p3700
This converter enables the connection of a M.2 NGFF SSD in 2280, 2260, 2242 and 2230 format.
Need M-key or NVME SSD, the B-key or B/M-key SSD cannot work.
The converter can be installed into your system internally through the U.2 68 pin interface.
Connector: U.2 SFF-8639 male & 67 pin M.2 NGFF key M slot
Supports M.2 NGFF modules in format 2280, 2260, 2242 and 2230 with key M
Maximum height of the components on the module: 1.5 mm
application of double-sided assembled modules supported
System requirements :
Windows 7/7-64/8/8-64/8.1/8.1-64/10/10-64, Linux Kernel 3.16
A free U.2 SFF-8639 interface or A free SFF-8643 interface
Note: for M-key or NVME SSD, please Update to add native driver support in NVM Express in Windows 7 and Windows Server 2008 R2
https://support.microsoft.com/en-us/kb/2990941
8. M.2 NVMe to USB 3.1 C (Gen 2) Enclosure External PCI-e M Key NVMe SSD Reader Adapter with USB C-C Cable by RIITOP
Feature
2018 New RIITOP M2 Nvme SSD External USB 3.1 Enclosure: Easy to make your PCI-e Based M Key Nvme SSD portable for data store or data transfer via USB C Port on your computerAluminum Case with a vented Design on both sides, will strengthen the effect of heat dissipation to protect your NVMe SSD well. And the LED indicators will transmit via vents when work.
RIITOP Nvme to USB Enclosure Compatibility: Support most of M.2 PCI-e M key SSDs, such as Samsung 950Pro/ 960Evo/ XP941/ PM951/ PM961/ SM951/ SM962 and so on. Only Support M.2 PCI-e Based M Key Nvme SSD
Note: NOT Support CLONE! NOT Support backup SSD with OS inside...DO NOT support PCI-e M Key AHCI SSD, SATA based B+M key or B Key SSD, Please check with the picture.
Package including: 1x M.2 NVMe to USB C Enclosure, 1x USB C To C Cable 30cm, 1x Screwdrive, 1x Protective Bag, Screws
Description
Specifications: Item: USB 3.1 TYPE-C NVMe SSD Enclosure. Size: 107*46*10mm. Material: Aluminum. Protocol: NVMe. Connector: USB TYPE-C 3.1. High Speed: 10Gbps. Support: 3D Game, 4K video ,HIFI Music, RAM Picture ect9. Goliton SFF-8639 NVME U.2 to NGFF M.2 M-Key PCIe SSD Adapter for Mainboard Replace Intel SSD 750 p3600 p3700
Feature
1. This converter enables the connection of a M.2 NGFF SSD in 2280, 2260, 2242 and 2230 format.2. Need M-key or NVME SSD, the B-key or B/M-key SSD cannot work.
3. The converter can be installed into your system internally through the U.2 68 pin interface.
4. Connector: U.2 SFF-8639 male & 67 pin M.2 NGFF key M slot
5. Supports M.2 NGFF modules in format 2280, 2260, 2242 and 2230 with key M
Description
Description:
1. This converter enables the connection of a M.2 NGFF SSD in 2280, 2260, 2242 and 2230 format.
2. Need M-key or NVME SSD, the B-key or B/M-key SSD cannot work.
3. The converter can be installed into your system internally through the U.2 68 pin interface.
4.Connector: U.2 SFF-8639 male & 67 pin M.2 NGFF key M slot
5. Supports M.2 NGFF modules in format 2280, 2260, 2242 and 2230 with key M
6. Maximum height of the components on the module: 1.5 mm
7. Application of double-sided assembled modules supported
System requirements :
Windows 7/7-64/8/8-64/8.1/8.1-64/10/10-64, Linux Kernel 3.16
A free U.2 SFF-8639 interface or A free SFF-8643 interface
Package include:
Only included the PCBA adapter like the photo show only
Goliton is a registered trademark protected by the US Trademark Law. Goliton products are sold by authorized sellers with Goliton package only.
10. M.2 NGFF Portable SSD Enclosure USB3.0 Case, Tanbin SATA Based B & M Key Solid State Disk Reader Adapter Converter as External Hard Drive Support 2230/2242
Feature
Support B key and B + M key interface (NOT support M key and PCI-E (Samsung 950/960 )).USB 3.0 5Gbps super-speed interface, 10 times faster than USB 2.0. Support UASP protocol.
Plug and play, hot swappable supported, adopting screws to fix the hard disk, make the built-in hard drive more safer.
Support System: Windows xp / Vista / Windows7 / 8 / 8.1 / Linux / MAC Free drive with USB.
Durable aluminium construction shell, stylish appearance and durable. Low heat, low consumption, shockproof, longer using life, with a small screwdriver included.
Description
Description:- High Speed USB3.0 to 2242 M.2 NGFF SSD Storage Case - A perfect solution for data transfer or data backup!
- This is a compact NGFF (M.2) SSD Enclosure which will allow you to plug in your NGFF (M.2) SSD and use it as a portable external drive
- By formatting this case with a drawer function, there is now extra protection for your hard drive. Downward compatible with USB 3.0/2.0 and 1.1,and the speed turn with it. this enclosure is a perfect solution for data transfer or data backup!
Features:
* Connects NGFF B Key SSD safely to computer via USB port.
* Compliant with PCI Express M.2 specification 1.0.
* Compliant with SATA 3.0 specification.
* Compliant with USB 3.0 specification.
* Transfer Rates Up to 5 Gbps when connected to a USB 3.0 port.
* Transfer Rates Up to 480 Mbps when connected to a USB 2.0 port.
* Supports SATA-based B Key NGFF SSD.
* Applicable SSD hard drive: support 22mm * 30mm / 42mm NGFF (M.2) Interface SSD hard drive.
* Easy installation & no driver required.
* No additional power required.
* Support boot function.
* Supports Plug & Play and Hot-Swapping.
* Support System: Windows xp / Vista / Windows7 / 8 / 8.1 / Linux / MAC Free drive with USB.
Please note that it ONLY supports SATA-based B Key SSD. DO NOT support PCI-E based B key & any M key SSD.
Package Includes:
- 1 * USB 3.0 to NGFF M.2 B Key SSD Enclosure. (SSD card is not included)
- 1 * 1X USB 3.0 Cable
- 1 * Screw Drivers
Recent Comments