Top raspberry pi gps module
If you looking for raspberry pi gps module then you are right place. We are searching for the best raspberry pi gps module on the market and analyze these products to provide you the best choice.
![Adafruit Ultimate GPS Breakout - 66 channel w/10 Hz updates [ADA746]](https://images-na.ssl-images-amazon.com/images/I/51-6yDhExjL.jpg)
1. SIM808 Module GSM GPRS GPS Development Board + IPX SMA GSM GPS Antenna Support 2G Network for Arduino Raspberry Pi Geekstory
Feature
This module only works with 2G Network but it support 2G 3G 4G SIM card. If your place is 3G Network, pls buy sim5320a Module. If you need 4G module, pls search SIM7100A in my store.It is used to open / close the input power supply for the module. When in use, please confirm the toggle switched to the OPEN state (near the board inside)
SMA antenna interface: there is a GSM antenna interface, a GPS antenna interface onboard and a BT antenna interface
USB interface: This interface is just use to update the firmware of SIM808 module
For documentation, please feel free to contact me.
Description
Description:1.Three power input interface: DC044 interface and V_IN and a lithium battery interface.
Note: The range of DC044 and V_IN pin voltage input is 5-26V, when use 5V as the power, be sure that power supply can provide 2A current. The range of voltage of Lithium battery input power is 3.5-4.2V.
2. Start button: When the board is power on, the LED (PWR) will light up. After a long press (about 2 second) on this button, other three LEDs will light. And one of them starts to flash; this suggests SIM808 is beginning to work. When the power supply, GSM and GPS antenna and SIM card are connected to the module correctly, the LED will be flash slowly (3Second de 1second light), that indicates the module is registered to the network, and you can make a call or do something else.
3. TTL serial interface: a TTL level interface. Notice: The pin of VMCU is used to control high level of TTL UART, so as to realize to match between 1.25V/3.3V /5V systems. For example, if you want to use the 51 MCU to control this board, the pin of VMCU should be connected the DC5V. And if use STM32 MCU, the pin of VMCU should be connected the DC3.3V. The pins of RXD is the RXD of SIM808 and the pins of TXD is the TXD of SIM808. The pin of V_IN can connect the Power, the function of this pin is the same as DC044.
Operation:
1. Preparation:
SIM808 SHIELD
DC9V adapter
USB-TTL module or other tools.
PC software
2. Hardware configurations
2.1 Connect USB-TTL to UART interface
USB-TTL SIM808
TXD RXD
RXD TXD
GND GND
2.2 Insert valid SIM card to SIMCARD holder.
2.3 Connect the GPS antenna and GSM antenna to the board
Connect the power adapter to the DC044 Interface
2.4 Change the switch
2.6 Press the POWKEY button for 2 second, the module will work and the other 3 LEDs will light
2. Diymall Vk-172 vk 172 Gmouse G-mouse Usb Gps Dongle Glonass Support Windows 10/8/7/vista/XP Raspberry PI B+ 3 Vehicle Aviation Tracker
Feature
with ublox 7020 chip,Support Windows Andorid Linux sytem, Raspberry PIand EMGRANDWindows Driver Link: https://www.u-blox.com/en/product/u-center-windows
NOTE: Please install driver before use it.Note: As the ceramic antenna is not big enough, the module can not get good signal indoor, please try it outdoor or install a signal booster in your room or office
gps data too google data need Conversion,calculation link: https://drive.google.com/open?id=1MwNTrqJtst3Dpl9qH8Mt3UJhs87ODdf9
pack of 2pcs link:https://www.amazon.com/dp/B01HF0K5WAWarranty: one year warranty, any question please feel free to contact
Description
Chip u-blox 7020 chipSupport Windows Andorid Linux sytem, Raspberry PIand EMGRAND car
VK-172 automatically adapt the baud rate, the baud rate has
any data output
Support Google Earth
Electrical properties:
Tracking sensitivity:-162dBm
Acquisition sensitivity:-160dBm
Cold Start Time: 29s
Warm start time:28s
Hot start time: 1s
Recapture Time: 0.1s
Package included
2 X VK-172 GMOUSE USB GPS/GLONASS USB
NOTE: The default output is the product GPS protocol data. You can test the software or serial commands to modify switch PS / GLONASS protocol data
How to install driver on windows 10?
After plugging in the device, let it do its thing installing a basic driver.
Here is the driver links
Windows Driver Link: https://www.u-blox.com/en/product/u-center-windows
NOTE
It can work with windows, linux system, but it can not work with IOS system
Windows Driver Link: https://www.u-blox.com/en/product/u-center-windows
3. AZDelivery GPS Module for Arduino and Raspberry Pi
Feature
u-blox GY-GPS6MV2 GPS Module for Arduino, Raspberry PI and Model Airplane ControllerAfter cold start, ready for operation in less than 30s, with a warm start within one second!
GPS module with data backup battery and external ceramic antenna; Tracking accuracy up to 2.50 m!
Dimensions (LxWxH) - GPS module: 36 x 26 x 4 mm; Antenna: 27 x 27 x 6.5 mm (45mm antenna cable)
Well-known high quality and fast delivery through Amazon Prime and purchase at AZDelivery!
Description
u-blox GY-GPS6MV2 GPS Module for Arduino, Raspberry PI and Model Airplane ControllerAfter cold start, ready for operation in less than 30s, with a warm start within one second!
GPS module with data backup battery and external ceramic antenna; Tracking accuracy up to 2.50 m!
Dimensions (LxWxH) - GPS module: 36 x 26 x 4 mm; Antenna: 27 x 27 x 6.5 mm (45mm antenna cable)
4. Adafruit Ultimate GPS Breakout - 66 channel w/10 Hz updates [ADA746]
Feature
-165 dBm sensitivity, 10 Hz updates, 66 channels5V friendly design and only 20mA current draw
Description
Note: This part was updated from Adafruit #99 (discontinued) to Adafruit #746 Adafruit believes this is the Ultimate GPS module, so they named it that. It's got everything you want and more5. Gowoops GPS Module with TTL Ceramic Passive Antenna for Arduino Raspberry Pi 2 3 B+ MCU
Feature
This is a small size item, and it has excellent performance. This item has data backup battery and LED signal indicator.Comes with 25 x 25mm ceramic passive antenna, strong star search ability.
Various parameters can be set via the serial port, and can be stored in the EEPROM, easy to use.
Compatible with 3.3V / 5V level, convenient for connection to a variety of microprocessor systems.
Built-in rechargeable backup battery, you can keep the ephemeris data when power down.
Description
User Manual for Rapsberry Pi: http://osoyoo.com/2016/10/25/use-rapsberry-pi-to-drive-u-blox-neo-6m-gps-module/User Manual for Arduino Mega2560: http://osoyoo.com/2016/10/25/use-mega2560-to-drive-gps/
Model: GPS-NEO-6M-001
Supply voltage: 3V / 5V power supply common
Antenna size: 25 x 25 mm
Module size: 26 x 39.5 mm
Mounting Hole diameter: 2mm
Default Baud Rate: 38400
Default output: NMEA0183 protocol accord
Note: The module is used outdoors, just needs a few minutes to locate.
Package include:
1 x GPS Module
6. Raspberry Pi GSM/GPRS/GNSS Bluetooth HAT Expansion Board GPS Module SIM868 Compatible With Raspberry Pi 2B 3B Zero Zero W Support Make a Call,Send Messagess,DataTransfer
Feature
Download link: www.waveshare.com/wiki/GSM/GPRS/GNSS_HATRaspberry Pi connectivity, compatible with Raspberry Pi 2B/3B/3B+/Zero/Zero W
Supports SMS, phone call, GPRS, DTMF, HTTP, FTP, MMS, email, etc.
Support GPS, COMPASS, Glonass, LBS base station positioning, omni-positioning
Please buy from Coolwell Technology directly for 100% original product and get technical support from Waveshare Team!
Description
DescriptionGSM/GPRS/GNSS/Bluetooth HAT for Raspberry Pi, Based on SIM868
This is a handy, low power Raspberry Pi HAT which features multi communication functionalities: GSM, GPRS, GNSS and Bluetooth.
It allows your Pi to easily make a telephone call, send messages, connect to wireless Internet, global position, transfer data via
Bluetooth, and so on.
Features
Raspberry Pi connectivity, compatible with Raspberry Pi 2B/3B/3B+/Zero/Zero W
Supports SMS, phone call, GPRS, DTMF, HTTP, FTP, MMS, email, etc.
Support GPS, COMPASS, Glonass, LBS base station positioning, omni-positioning
Bluetooth 3.0, supports data transferring through Bluetooth
Onboard USB TO UART converter CP2102 for UART debugging
6x LEDs for indicating the module working status
SIM card slot for 1.8V/3V SIM card
RTC with backup battery holder
Baudrate auto detection (1200bps ~115200bps)
Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands)
Supports SIM application toolkit: GSM 11.14 Release 99
Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)
Package Contains
GSM/GPRS/GNSS HAT x1
GSM Antenna x1
GPS External Antenna (B) x1
Bluetooth Antenna x1
USB type A plug to micro plug cable x1
RPi screws pack (2pcs) x1
Development Resources
Wiki : www.waveshare.com/wiki/GSM/GPRS/GNSS_HAT
7. Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit
Feature
165 dBm sensitivity, 10 Hz updates, 66 channelsBuilt in Real Time Clock (RTC) - slot in a CR1220 backup battery for 7-years or more of timekeeping even if the Raspberry Pi is off!
Internal patch antenna which works quite well when used outdoors + u.FL connector for external active antenna for when used indoors or in locations without a clear sky view
Fix status LED blinks to let you know when the GPS has determined the current coordinates
Raspberry Pi *not* included
Description
This new HAT from Adafruit adds their celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model A+ or B+ We spun up a HAT based on our Ultimate GPS, added a coin-cell holder for RTC usage, break-outs for all the Raspberry Pi's extra pins, and plenty of prototyping area for adding LEDs, sensors, and more. Please note, this HAT takes over the Raspberry Pi's hardware UART to send/receive data to and from the GPS module. So, if you need to use the RX/TX pins with a console cable, you cannot also use this HAT. Instead, you'll have to use a composite or HDMI monitor and keyboard to log in, or use ssh to connect over the network to your Pi. Read up on Adafruit's tutorial for more information on how to use this fine HAT. Comes as a fully assembled GPS + PCB and an additional 2x20 GPIO header. Some light soldering is required to attach the 2x20 GPIO header to the HAT but it's fast and easy for anyone with a soldering iron and solder. This HAT does not come with a 12mm coin battery! A CR1220 will let you use the real-time-clock capability of the GPS HAT.8. BerryGPS-IMUv2 - GPS and 10DOF for The Raspberry Pi - Accelerometer, Gyroscope, Magnetometer and Barometric/Altitude Sensor
Feature
Compatible with all versions of Raspberry Pi.High quality GPS module which is able to track 22 satellites.
Internal antenna
Instructions and guides at http://ozzmaker.com
10DOF - An Accelerometer, Gyroscope, Magnetometer and Barometric/Altitude Sensor
Description
BerryGPS-IMUv2 has been specifically designed for the Raspberry Pi Zero. It is also compatible with all other versions of Raspberry Pi.BerryGPS-IMUv2 uses the M20048 from Antenova, which is a high quality GPS module which is able to track 22 satellites.
This module is also equip with 10DOF. The same sensors that are found on the BerryIMU
The sensors found on the BerryGPS-IMUv2 are:
- Accelerometer
- Gyroscope
- Magnetometer (Compass)
- Barometric/Altitude
- Temperature
Features
Built in antenna: BerryGPS-IMUv2 comes with an inbuilt antenna.
SupCap: The SuperCap keeps the phemeris data stored in the battery backup RAM for 4 hours. This allows for faster acquisitions when the module is power cycled.
Fix indicator: The fix LED will flash once a second when a fix has been obtained. The fix signal is also presented on an output pin.
PPS: BerryGPS-IMUv2 also includes Pulse Per Second(PPS) functionality. With a LED which will flash on every pulse and an output pin to be used by a microcontroller for time syncing.
Standby Pin: Includes a pin to place the GPS module into standby mode.
Periodic mode: Periodic mode is a module controlled mode that reduces current consumption by only waking the module for short periods to maintain fix data.
Connection for external antenna: BerryGPS-IMUv2 also includes a uFL connector for an external antenna, which can be used when BerryGPS doesn't have clear access to the sky.
BerryGPS-IUM comes with;
BerryGPS-IMUv2 PCB
1 x Female header
4 x Nylon standoffs, nuts and screws
Raspberry Pi not included
9. DIYmall NEO-6M GPS Module with EEPROM for MWC/AeroQuad with Antenna for Arduino Flight Control Aircraft
Feature
Document link: https://engineersportal.com/blog/2018/5/9/comparing-iphone-gps-against-neo-6m-gy-gps6m-gps-module-with-arduinoYoutube link: https://www.youtube.com/watch?v=VziqwqLaGso
LED signal indicator,With data backup battery
EEPROM power down to save the configuration parameters data
One year warranty,we offer free sample to anyone who can make projects,please contact.Thanks.
Description
NEO-6M GPS Module with EEPROM for MWC/AeroQuad with Antenna for Flight Control and AircraftDescription:
GPS modules NEO-6M, 3V-5V power supply Universal
Module with ceramic destined antenna, super signal
EEPROM power down to save the configuration parameters data
LED signal indicator
With data backup battery
The default baud rate: 9600
Mounting Hole 3mm
Module size 23mm * 30mm
Antenna size :25mm*25mm
Cable Length:50mm
Package Included:
1 X GPS module
10. MakerFocus GPS Module 51 Microcontroller Ublox GPS Compatible NEO-6M STM32 Arduino Navigation Satellite Positioning GT-U7
Feature
Link to teach you how to use this module: https://www.youtube.com/watch?v=bgOZLgaLa0g. Library: http://arduiniana.org/libraries/tinygpsplus/. Please feel free to email us if you have any questions or you would have a bulk order, how to email us? Click "MakerFocus" and "Ask a question". Looking for your consultation!GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage.
With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect.
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna!
With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned.
Description
GPS Module 51 Microcontroller Ublox GPS Compatible NEO-6M STM32 Arduino Navigation Satellite Positioning GT-U7Description:
GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M.
With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect.
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna!
Features:
GT-U7 module, with high sensitivity, low power consumption.
Miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage.
In the ordinary GPS receiver module can not locate the place, such as narrow urban sky, dense jungle environment, GT-U7 can be high-precision positioning.
Module with high sensitivity, small static drift, low power and lightweight volume.
With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned
Operating voltage: 3.6V-5V (or direct usb power supply)
Operating baud rate: 9600 (can be modified)
Onboard rechargeable button battery
Onboard E2PROM can save parameter data
NEMA output format is compatible with NEO-6M
Size: 27.6mm * 26.6mm can be inserted or selected patch (with positioning holes)
Application:
Vehicle-mounted
Handheld devices such as PDAs
Vehicle monitoring
Mobile phones, camcorders and other mobile positioning systems
Sharing bike
Sharing mobile power
Package Including
1 * GT-U7 GPS Module
1 * IPX interface active antenna
Recent Comments